Knowing Plumbing Basics is Essential When Installing a Bathtub
Knowing Plumbing Basics is Essential When Installing a Bathtub
Blog Article
We have encountered the article relating to How to Install a Bathtub Yourself listed below on the internet and felt it made perfect sense to relate it with you over here.
Mounting a bath tub isn't specifically brain surgery, but it does need solid plumbing, carpentry, and sometimes, tiling skills. Replacing an old bath tub with a brand-new one is additionally a reasonably hard job. If the old bathtub is conveniently accessible, the job can relocate rapidly; if you have to open up a wall surface to get rid of the old bathtub and position the new tub, the task is a lot harder. In either case, the task is within a home handyman's skills, although you will certainly need an assistant to leave the old bathtub and embeded in the new one. Make sure you have actually certified on your own for the task as well as are comfortable attempting it. Rather than hiring a professional to take over a halfway-completed job, it is much better to think about employing one before you begin. Opportunities are you might need a professional plumber to make tube links.
This write-up will help you set up a brand-new bath tub in your washroom if you have actually currently purchased a brand-new bathtub as well as do not require to alter the plan of your previous water pipes.
Your tools as well as material checklist ought to make up the following:
Removing Old Taps
If you need to replace old taps with brand-new ones as a part of your setup, then the first thing you ought to do is disconnect the water. After doing so, switch on the faucets to drain any kind of water remaining in the system. The procedure of removing the existing taps can be fairly bothersome as a result of the limited gain access to that is usually the situation.
Utilize a container wrench (crowsfoot spanner) or a faucet device to undo the nut that connects the supply pipelines to the faucets. Have a fabric ready for the remaining water that will originate from the pipelines. When the supply pipes have been gotten rid of, make use of the exact same tool to loosen up the nut that holds the faucets onto the bath/basin. You will need to stop the solitary taps from transforming throughout this process. As soon as the faucets have been gotten rid of, the holes in the bath/basin will certainly have to be cleaned of any kind of old sealing substance.
Before going on to fit the new faucets, compare the pipeline connections on the old faucets to the new faucets. If the old faucets are longer than the brand-new taps, after that a shank adapter is needed for the brand-new faucets to fit.
Suitable New Touches
If the tails of the brand-new taps are plastic, after that you will certainly need a plastic port to avoid damage to the thread. One end of the connector fits on the plastic tail of the faucet and also the various other end gives a link to the existing supply pipelines.
If you need to fit a monobloc, after that you will require reducing couplers, which connects the 10mm pipe of the monobloc to the basic 15mm supply pipeline.
Next, place the tap in the installing opening in the bath/basin making sure that the washers remain in place between the faucet as well as the sink. Protect the tap in position with the supplier offered backnut. When the tap is firmly in position, the supply pipes can be linked to the tails of the taps. The taps can either be connected by utilizing corrugated copper piping or with typical tap ports. The previous type must be attached to the faucet ends first, tightening only by hand. The supply pipes can later on be linked to the other end. Tighten up both ends with a spanner after both ends have actually been linked.
Setting up the Bath tub
Making use of both wooden boards under its feet, place the tub in the needed placement. The wooden boards are valuable in equally spreading the weight of the bath tub over the location of the boards instead of concentrating all the weight onto 4 small points.
The next objective is to ensure that the bath tub is leveled all round. This can be accomplished by examining the level as well as adjusting the feet on the bath tub up until the level reviews degree.
To mount taps, fit the bottom of the furthest adaptable tap adapter to the proper supply pipeline by making a compression sign up with; then do the very same for the other faucet.
Turn on the water and also examine all joints and also new pipework for leaks and tighten them if essential. Fill the tub and also inspect the overflow outlet as well as the normal electrical outlet for leaks.
Lastly, repair the bathroom paneling as explained in the producer's user's manual. Tiling and sealing around the bath tub ought to wait up until the bathtub has actually been used at the very least once as this will resolve it right into its final placement.
Preparing for the Installment
First of all, the sustaining framework supplied with the bathroom ought to be fitted (if called for) according to the producer's directions. Next off, fit the taps or mixer to the tub. When suitable the tap block, it is very important to make sure that if the tap comes with a plastic washer, it is fitted in between the bath as well as the taps. On a plastic bathroom, it is likewise reasonable to fit a sustaining plate under the taps system to avoid pressure on the tub.
Fit the adaptable faucet connectors to the bottom of both taps making use of 2 nuts and olives (in some cases supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the electrical outlet with the hole in the bath. Utilize the nut supplied by the supplier to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the flexible overflow pipeline to the overflow outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bath. See to it you make use of all of the supplied washing machines.
Connect the catch to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Connect all-time low of the overflow tube in a similar manner.The bath must currently prepare to be suited its last position.
Tiling Around the Tub
In the area where the bath fulfills the ceramic tile, it is required to secure the joins with a silicone rubber caulking. This is necessary as the fitting can move sufficient to break a stiff seal, causing the water to penetrate the wall in between the bathroom and the tiling, resulting in problems with dampness and feasible leakages to the ceiling listed below.
You can select from a variety of coloured sealers to assimilate your components as well as fittings. They are marketed in tubes as well as cartridges, and are capable of securing gaps approximately a width of 3mm (1/8 inch). If you have a bigger void to fill up, you can load it with twists of drenched newspaper or soft rope. Keep in mind to constantly fill the bath tub with water before sealing, to allow for the activity experienced when the bathtub is in usage. The sealant can fracture rather early if you do not consider this movement prior to sealing.
Additionally, ceramic coving or quadrant floor tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are likewise conveniently available on the marketplace. It is a good idea to fit the floor tiles using water-resistant or water resistant sticky as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you really like more info about How to Install a Bathtub Yourself? Place feedback down the page. We'd be glad to find out your insights about this blog. We are looking forward that you come back again soon. Do you know about another individual who is interested in the topic? Please feel free to share it. I am grateful for your time. Visit us again soon.
Book My Estimate Report this page